How To Update Galaxy Note 4 N910C (Exynos) Android 4.4.4 Kit-Kat Official Firmware

Well well well, Galaxy Note 4 is finally available for Customizations, since the Rooting method is available and also some of the Official ROMs are also available with exclusive tag of countries. Galaxy Note 4 will be the biggest flop for Samsung as nothing has changes in it and Galaxy Note 3 and Galaxy Note 3 is cheap and we all know if you can get better specs in Nexus 5 why go for iPhone 6 and if you are getting the exact same things in Galaxy Note 3, why upgrade to Note 4, it is same like, if you have a DSLR with built-in Focus motor and a D lens, why upgrade to a built-in focus motor lens. Nonetheless, the Official ROMs are available and it is our job to give them to you.This update is exclusive for Thailand, however, you can try this ROM on any other Galaxy Note 4, the baseband will be different, who know you might have some Network issues, but this is what Android is, you can try different methods and always come back to the Original thing without any problem.

Samsung has Samsung Kies to Update the device if you can’t get it directly on your device. Must Know, that you need to be on the Official Firmware to get this update. This update can be download via Samsung Kies, but the case is different here besides, my experience with Samsung Kies is way too bad,  you can just check the OTA update, it will be there. But if it’s not, we have an even simple solution for you, download and flash it manually. Manual Installation is great, if you coming from a Custom ROM and possibly the only way to get back to Official ROM.

Samsung-Galaxy-Note-4-1

We are going to install official Android 4.4.4 KtiKat firmware on our beloved Galaxy Note 4 N910c using Odin3 in the following post. While this is an official firmware, you don’t really need to worry about anything. All you have to do is, you need to follow the instructions carefully and get it done flawlessly. Let’s go through the early preparations and then flash this firmware.

Early Preparations:

1. This guide is only for Galaxy Note 4 N910C {Thailand}

Make sure that your device is exactly as mentioned above. To check out what device you have, go to Settings > More/General > About Device or Settings > About Device and match the model number. Be careful about the device model number, flashing a file on a device not listed here might result in bricking it up. In that case, we may not be held responsible.

2. Battery should be charged at least 60%!

Your device’s battery shouldn’t be weak. In case your device goes dead during the flashing process, your device may get soft bricked and you might be in need of flashing stock firmware and that will ultimately result in wiping up your data as well. So, make sure that you charge your device before you start the flashing process.

3. Use the OEM data-cable to establish connection!

Always use the original data cable to establish connection between your Android device and your computer / laptop. Using ordinary data cables might interrupt the flashing process, so to avoid any mishap, you need to meet this requirement as well.

4. Backup everything!

Just to be on the safe side, you may consider backing up each and everything from your Android device. This is highly recommended so that in case anything goes wrong, you still have the access to all of your data and you can restore it immediately. Also, clean install is always recommended, that means you will probably have to wipe your device to install the new firmware. So, you may backup everything as listed below.

5. Turn off Samsung Kies and other softwares while using Odin3!

Make sure that you turn off Samsung Kies while using Odin3 flashtool. Samsung Kies will interrupt Odin3 and will result in causing errors and may not let you flash your desired firmware. Also, make sure that you turn off any antivirus software you’ve installed and also disable firewall to avoid any connection and flashing issues.

How To Install Official Android 4.4.4 KitKat On Galaxy Note 4 N910C

Downloads Required:

  1. Download and extract Odin3 v3.09.
  2. Download and Install Samsung USB drivers .
  3. Download and extract firmware file: Link

Method:

  1. Wipe your device complete in order to attain a neat installation.
  2. Open Odin3.exe.
  3. Put your Galaxy Note 4 in download mode. To do so, turn it off and wait for 10 seconds. Turn it on by pressing and holding Volume Down + Home Button + Power Key simultaneously, You should see a warning, press Volume Up to continue. In case this method doesn’t work for you, try one from this guide.
  4. Connect your device to your PC.
  5. As soon as Odin detects your phone, the ID:COM box should turn blue.  Make sure that you’ve installed Samsung USB drivers before connecting.
  6. For Odin 3.09 hit the AP tab. Select the firmware.tar.md5 or firmware.tar, that you downloaded and extracted above.
  7. If you’re using Odin 3.07, you will select “PDA” tab instead of the AP tab, rest of the options remain untouched.
  8. Make sure that the options selected in your Odin are exactly as shown in the pic.Odin-3.09-explained.-2
  9. Hit start and wait till the firmware  flashing is complete, as soon as your device restarts, remove it from PC.
  10. Wait for your device to reboot, as soon as it reboots check out the new firmware!
  11. That’s all!

© 2016 TechBeasts. All rights reserved.· Entries RSS · Comments RSS
TechBeasts.com is not associated with Google, Samsung or any other OS provider and smartphone manufacturer. We are an unofficial fan site.